rfid print process resolution: integrated operation for data writing and labeling
RFID Knowledge

rfid print process resolution: integrated operation for data writing and labeling

PublishedShanghai Zejie Smart Technology Co., Ltd.

RFID tags are not "printed." They're "written and made".

Many people think that the RFID label is like a normal non-dry tape, and feed in a roll of paper. It's really different -- it's just ink on the face, and the RFID tag is in the same process, and then the data is in the chip, and then the face, glue, paper, and the stylist shape is in one form. The data are tied to death between the labeling, missing one, missing one, wrong one, and the whole lot is gone.

What steps are included in the integrated operation?

A complete RFID label line, from the entry of raw materials to the bottom of the finished product, cannot be reversed:

  1. Antenna base rolls: an antenna ring is printed on the PET membrane with silver or aluminium.
  2. Chip binding: IC is fixed to the antenna welding plate by re-inverting or pasting.
  3. Inlay primary (inlay means the uncut middle of the label): Online electrical performance test, confirming that the chip is read and written.
  4. Composite face-on: The layer (copper, synthetic paper or PP) is bound with glue and Grasing paper (a silicate coated sticky paper) to inlay.
  5. Modular cut-off: Cut the outline of the label with a cylindrical knife while avoiding chip and antenna positions.
  6. Sub-volumes: Cut in a single volume or sheet and package them into the library.

If a desktop RFID printer (a door shop or warehouse site-marking) is used, the process is compressed into a roll-down code and a print stubble is cut out in three steps, but it is still "write by hand" by nature.

What exactly is the data going on in this step?

A UHF RFID chip usually has three storage areas:

The writing is not "sweeped and done" but it is a four-step process: the RF-activated chip (UHF working frequency 860-960 MHz, HF 13.56MHz) is written back at ISO/IEC 18000-63 or ISO 14443 data. The writing rhythm on the industrial line (the time taken to complete the code for individual labels) is usually 30-80 milliseconds per piece, and it is done immediately by rereading the results, so that this one is considered eligible.

Key control point for label formation

The form looks like a "print + cut" but the RFID label is much more stringent than the normal tag:

Why must writing and forming be integrated?

Dismantling the writing and formation into two sections is theoretically feasible - first, to make a blank label and then to write data on another device. But there are no problems in real-life exercises:

  1. The secondary handling introduced static, which could penetrate the protection circuit of the chip ESD - the general chip HBM (human discharge model) at around 2 kV.
  2. The segmenting exercise means that two positioning accuracy superimposes, and the error in the position of writing to antennas and print antennas can easily exceed the tolerance window of ± 0.3 mm.
  3. There is a significant efficiency gap - integrated production lines can produce 200-600 labels per minute, and sub-working operations usually can only reach 50-100/minute.

So the mainstream RFID label line is all looking for "a process complete": a scroll, composite, writing, printing, agility, testing, a string of paper, any one of which is found to be bad, immediately receiving feedback and automatically removing it.

A couple of easy-to-touch pits.

Several typical problems have been observed in the actual project:

The commonality of these problems is that each does not have to stop the production line, but it drags the positive rate from more than 99 per cent to 95 per cent or even lower, and accumulates in a significant loss.

Shanghai's Accomplishment

Shanghai-based Chettech, in its RFID tag line program, usually aligns "writing" and "moderate" as two main lines -- the msace action, the mosaic action, the second-scale action, with a buffer between which the encoder and the scissor are stringed up to match the speed curve. The whole beat is determined by the slowest, not by the fastest, so that the device does not turn empty because of waiting for each other.

In addition, an online optical test (AOI, i.e. automatic comparison of product images with cameras) is added between the writing and the modulations, which removes both physical and electrical defects in a synchronized manner to avoid the discovery of undesirable products by the client.

How do you judge a line is not good?

Several indicators that can be field-tested:

Indicators Qualified Lines Scope of reference
Writing Good Rate ≥99.5% 99.5%~99.9%
More accuracy ± 0.2 mm or less ±0.15~0.2mm
Line beat Depending on the product. 150-400 inlay lines, 80-250 inch modulate cutters
Read-outs Consistency 100 tests. Standard deviation design value 10%

The four indicators are met and the production line is generally safe to operate; if a given item is clearly low, the batch of raw materials, equipment calibration and environmental parameters are checked before process adjustments are considered.

I'll finish the sentence.

The RFID label "print" is essentially a process of writing data and physically binding them. Splitting isn't impossible, it's not cost-effective or good. Read the logic, read the production line and quote, so that they don't go with surface parameters.