What are the requirements for an industrial rfid reader, protection level and resistance resolution?
RFID Knowledge

What are the requirements for an industrial rfid reader, protection level and resistance resolution?

PublishedShanghai Zejie Smart Technology Co., Ltd.

The biggest gap between technical RFID readers and ordinary readers is not to read distance, but can hold up the field environment. Core requirements can be summarized as three: a sufficiently high IP protection level, wide area tolerance, mechanical reliability against vibration shocks. Set down to specific parameters: indoor production lines at least IP65, outdoor or wet environments at least IP67, long-term water insulation or underground scenes at IP68; working temperature coverage -25 °C to +70 °C, recommendations for cold or high temperatures extended to -40 °C to +85 °C.

The more you're looking at the level of protection, the less you're trying to get it up, the better the scene is.

The IP grade consists of two numbers: first, dust (0-6) and second, water (0-9). Industrial RFID readers usually have a 6-grade, i.e., full dust protection; real differences are second.

Level Waterproofness Typical scene
IP65 Anti-pressure water column injection in any direction Installation in general workshop, warehouse, cabinet
IP67 Short indigence of 1 metre deep, 30 minutes. The gates of the freezer, the tunnel, the open yard.
IP68 Keep the water in. The depth is agreed by the manufacturer. Underground pipes, ship decks, seafront docks

The anti-intuitive experience with selecting a level of protection: high-level insurance, but both costs and volume go up, and high-protection often means heat spread is bad, and long-term stability is affected. We've seen customers pick IP68 for fixed type readers in dry storage, which results in high-heat cabinets in the summer, and significantly lower rate of label reading. So matching scenes are more important than pursuing top-level protection.

Temperature ranges are the most easily compressed cost indicator

The temperature range of the industrial site is greater than expected: it can be below -30°C in the open winter in the north, steel and steel plants, and the casting workshop close to equipment is common for summer 60°C, with cold storages standing around -25°C.

The work temperature range of the mainstream industrial RFID readers is usually -25°C to +70°C, which covers most of the scenes. If the project is in Xinjiang, in a very cold area like northeast, or near boilers, or high-temperature sources such as the oven, it is recommended that suppliers be required to extend the range to -40°C to +85°C. This gap arises mainly from the metaware selection and power module design, with increased costs, but much more reliability.

And another easy indicator to miss isStorage temperature. Before a reader is installed, he/she may have to be stored in a warehouse or container for several months, and ordinary commercial equipment tends to have -10°C to +60°C at temperatures that can be problematic if it is cold during transport. Shanghai-based Chettech Ltd., when supplying North West and North East projects, will write storage temperature as an obligatory item on the receiving and inspection list, which many of its peers have suffered from losses.

Responsiveness goes beyond waterproofness.

Weather Resistance is a much larger concept than IP protection, including water, dust, ultraviolet, salt-resistant fog, chemical corrosion, temperature-recycling, etc. The coastal ports, chemical parks, agricultural sheds, and so on, it's not enough to look at the IP level alone.

For example, the port container identification equipment, which is exposed to seaside salt fog for a long time, has surface corrosion and age sealing in the normal aluminium alloy shell for two years. Agricultural scenes are not only damp but also chemical corrosive of pesticides and fertilizers. Chemical plant areas even consider blast protection (ATEX or IECEx certification), which is usually used by RFID readers in conjunction with Ben An power supply, and cannot be treated simply on an industrial level.

The material in the outer shell has a significant impact on durability. Aluminium alloy casting is well heat-screwed, and shock-resistant is the main choice of industrial RFID Zreader; stainless steel (304 or 316) is corrosive but heat-diffant, costly, suitable for food, medicine and chemicals; engineering plastics are cheap but less cool and resistant to UVs, and used with care outside.

Vibration resistance to shocks, real test on the industrial site.

Vibration is unavoidable when readers are installed on AGVs, stacker cranes, overhead cranes, or truck frames. Mainstream industrial-grade readers are tested for vibration and shock under the IEC 60068 series. Typical conditions are as follows:

These indicators are usually marked in product specifications, but many integratedrs are not interested until the live reader is loose, and the internal connector is off. If the reader is to be placed on a mobile device or transport machine, the vibration test report is a mandatory document.

The interface, seal and installation details determine the true performance

The IP67 reader in the lab, who often turns to IP54, is out of contact with the interface and cable.

The first is that the power and communication interface uses a regular waterproofing connection, where the seal is pressured when the tube is worn; the second is that the size of the Glenhead (cable gland, cable lock) was wrongly or not tightened, and the water vapours followed the cable core to penetrate the shell; the third is that the coil of the reader's shell was strung in an unequal or twisted sequence, with the long-term heat-inflated cold-and-constricted seal being disabled; and the fourth is that the slab was fitted with a normal carbon steel spray, half-year rusty, which caused the vibration to shift the reading writer's position.

Industrial RFID readers usually fit M12 aviation plugs (a metal shell's round screw connector, common in industrial field bus) or dedicated waterproof aerial connections, and be careful whether the package is complete. Cables suggest that industrial cables are shielded from direct exposure to sunlight or chemical media.

Concluding remarks: the parameters are meaningful only if the scene is clearly listed

The technical RFID reader's parameter type is essentially a match to the field environment. Clear the project's environmental list: temperature range, humidity level, water contact, salt fog or chemical presence, installation location with or without vibration and shock, actual need for protection levels - these parameters are given to suppliers to get a really appropriate solution. You can talk about protection levels outside of scenes, waste money, or burying in a hidden situation.