Structure design for toreproof rfid electronic tags and principles of warning against breaking down
RFID Knowledge

Structure design for toreproof rfid electronic tags and principles of warning against breaking down

PublishedShanghai Zejie Smart Technology Co., Ltd.

Core: Make the damage act itself a visible signal.

The principle of the RFID tag is not complicated, but it's a physical event that "labels are broken" and it turns into electrical anomalies that can be read in a reader. The common approach is two ways: one to break the circuit -- to connect antennas or chips directly to external forces, to read the signal missing; the other to read the short circuit -- to create new circuits during destruction through special structures, to read signals mutation or to read a pre-set "alarm code." The two paths are often used in actual products, because a single mechanism is easily bypassed.

This design is a requirement for the application scenario: if the label is unsupervised for long periods, the simple "not read" is not a good way to judge the tearing -- or failure to read it may be a problem with equipment failure or distance. So mature programs often require readers to read labels while reading a state word, and then change the status word is a real alarm.

Several key structural levels

Antenna

The antenna is usually made on PET or PI film, printed with aluminium etching or silver. The key to the protection design is not in the shape of the antenna, but in the way it connects to the wiring between the antenna and the chip welding. The normal label is connected; the object tag will deliberately stretch the line, make it thin, even go around the edge of the label, and break these lines when the external force rips.

The fine width is typically between 0.2 and 0.3 mm, and the distance between lines is nuanced - too close to being cut off by a single slash at the same time, and too thin to be sensitive. The empirical value is that the width of the line is between 1:1 and 1:1.5.

The connection between the chip and the base.

The common inlay chip is fixed to the base with a conductor glue or welding, and the connection points are small, and external force is difficult to break. Tore-proof labels are designed -- exposing the link points to vulnerable grounding, forcing damage actions to pass through them. This is a structural reverse design thinking.

Tore-prone and adhesive

There's a layer of base, usually thin film or surface-treated coating that's less dense than the base. When someone tries to tear it, the layer is out before the glue, which leads to the tag being ripped but not to the whole piece -- the damageer gets the pieces, and the integrity of the label has been compromised.

The choice of adhesive is also refined. The general acrylic acid is strong enough to leave a mark when it is torn, and the rubber-based glue is high in initial viscosity but with low long-term reliability. The most common use in the toreproof scene is modified acrylic acid, which is moderate in initial viscosity, and reaches its final strength after 72 hours, both to ensure that the adhesion is stable and to make the tiered mechanism work.

How did the failed alarm trigger it?

Break-up trigger

If an antenna trace breaks and opens the chip's power circuit, the energy from the reader can no longer power the chip. The reader gets no data even within its normal range, and the back-end system treats this as a lost tag connection. A missed read alone cannot tell you whether the equipment failed or the tag was peeled off. A heartbeat mechanism is therefore commonly used: the reader polls every 3–5 seconds and raises an alert only after two consecutive missed reads, filtering out occasional interference.

Short circuit trigger and alarm code

And the more clever design is to create new circuits for damage. For example, a backup walker that is connected to an antenna near the chip, which is usually broken, but when external forces deform or break the base, this backline connects to the main antenna and forms short circuits. When the chip detects this short path, it puts "1" on one of the status senders, and the next time the reader reads it, there are alarm marks in the state note.

Some of the chips also support a self-defined warning code, which separates "torn" from "torn" from "torn" with high temperature damage by laying short paths in multiple different positions, each of which corresponds to one position. The cost of the chip increases, but it brings more precise ways of destroying.

The pits that were stepped on in the actual project.

Shanghai-based Scratch technology has encountered a situation in the storage-type customer label project: labels are placed on plastics, using an environment that is a constant temperature warehouse, and the torn structure should not have been triggered. But 3% of the user's feedback within a week was turned into warning numbers, which were checked at the scene, where forklifts were scrambled with each other, leading to a distortion of the paste position, and the sub-levels were activated.

The problem is not design defects, but design sufficiency. Then the critical pull of the layer is raised from 8N to 15N, and the bump is no longer triggered by error, at the cost of real human tearing takes more energy to break labels. It's a trade-off between typical sensitivity and anti-fault, with no standard answer, and only on the basis of the scene.

Another pitfall is metal. Mounting an RFID tag on metal substantially detunes the antenna and affects the sensitivity of tamper-evident designs. A common solution is to add foam or a magnetic RF absorber to the underside, spacing the antenna 4–5 mm from the metal. Many applications can accommodate that thickness. For an ultrathin tag, the compromise has to be in chip selection.

A few things that you can easily ignore when you're on the ground.

First, protocol compatibility. Most tamper-evident RFID tags use UHF EPC Class 1 Gen 2, but chip vendors define status words differently. One vendor's alarm bit might be another's reserved bit. Test samples before buying in bulk instead of relying on the protocol description alone.

Second, read and write. Even if the label is designed correctly, if the reader side does not open a state filter, the Query interval is set short, it will still generate a lot of false alarms. Backstage systems need to be updated simultaneously -- many of the ready-made WMS defaults only "read or not" -- and they need to be developed twice to handle the alert status.

And third, the evidence after the failure. The alarm triggered it, and then? If there's no camera on the scene, the alarm itself is just a time stamp. The more mature solution is to connect RFID readers with door-barrel, video-activated, automatic access to the last 30 seconds of video footage when the alarm triggers. This mechanism is almost necessary in the precious asset scene.

And back to the question at the beginning: The tore-proof RFID label is not just a "torn" label, it's a combination of projects that transform destruction into readable signals, circuits+ protocol+ systems. Structure design is an entry point, and real reliability comes from every level of reasonable trade-off.