Insinuation material to address RFID metal interference
The RFID industry in my country has grown over a decade, and now it is more sophisticated, especially for the last two years, as the country actively encourages and promotes healthy growth in its industries, with various factors continuing to increase its growth steadily.
There is a consensus on the frequency standard-setting of RFID. The current international and more common frequency is 13.56 MHz, 13.56 MHz's high-frequency HFID technology, which is stable, priced, and has a range of read distance and practical applications that match, therefore, its wide application in terms of bus cards, mobile phone payments, especially in South Korea, Japan, etc.
The RFID electronic labels are often used in metal environments, and when the RFID electronic tags are near to metals, because of their strong resonance with electromagnetic waves, they are accompanied by a diminished signal, closer distance from reading cards, and serious interference is associated with failure. The current common solution is to have suction material on the back side of the electronic tag.
The RFID system is a device for the electronic label or non-contact smartcards (e.g. smartphones with brushing) and for the issuance of instructions on electronic tags and for the collection of feedback from electronic labels, also known as RFID card readers or readers. As shown in figure 1, to enable other devices to display or use these data, it can generally be used to host an interface with RS232 protocols, so that information can be transmitted with external equipment.
Because it's a passive electronic label, the energy needed to work with chips and storage in an electronic label is provided by a reader, which communicates with an electronic label through the principle of electromagnetic coupling, which is created by the reading instrument's antenna.
The high frequency electromagnetic field is generated by the antenna ring of the reader, and then the magnetic field runs through the space around the cross-section and the circle. According to the label's usage frequency 13.56 MHz, its wavelength is 22.1 m, far more than the distance of the reader's antenna and electronic tags, so that the inter-tangible electromagnetic field can be treated as a simple intersectional magnetic field from the reading machine to the antenna.
By adjusting the electron labels' antenna and capacitors to form a resonance circuit, aligning to the R/C specified launch frequency 13.56 MHz, the RFID tag reading card distance is proportional to the power transfer efficiency of the two sets of the wiring and electronic labels, which are at a positive level, as well as the distance between them, which is the reason for the limit in the RFID tag reading card distance.
For the RFID electronic labels used under 13.56 MHz, its maximum reading and writing distance is usually around 10 cm, and the current consumption of chips is roughly 1 mn. Because as the frequency increases, the electro-labelling loops required are electrons that show a decrease in the number of coils, typically at that frequency, with a typical Twist of 3-10 mm.
RFIDThe distance of the label reading card is not only related to itself, but also has a strong bearing on its environment. When using an electrons-coated radio frequency recognition system, it is often requested that the antennas of the reader or electronic tag be installed directly on the metal surface. However, it is impossible to install magnetic antennas directly on the metal surface.
Because the antenna magnetic fluxes through the metal surface generate a sensor vortex, which, according to the law of the subtidal law, can counter-acting the field of the antenna and cause a rapid decline in the magnetic field on the metal surface so that the distance between data reading by readers and electronic labels will be seriously affected, or even may be misread or read unsuccessful. Whether the magnet field created by the wire itself on the metal surface is the same from outside, it is also the site close to the metal plate (the electronic tag is on the metal surface).
There is a consensus on the frequency standard-setting of RFID. The current international and more common frequency is 13.56 MHz, 13.56 MHz's high-frequency HFID technology, which is stable, priced, and has a range of read distance and practical applications that match, therefore, its wide application in terms of bus cards, mobile phone payments, especially in South Korea, Japan, etc.
The RFID electronic labels are often used in metal environments, and when the RFID electronic tags are near to metals, because of their strong resonance with electromagnetic waves, they are accompanied by a diminished signal, closer distance from reading cards, and serious interference is associated with failure. The current common solution is to have suction material on the back side of the electronic tag.
The RFID system is a device for the electronic label or non-contact smartcards (e.g. smartphones with brushing) and for the issuance of instructions on electronic tags and for the collection of feedback from electronic labels, also known as RFID card readers or readers. As shown in figure 1, to enable other devices to display or use these data, it can generally be used to host an interface with RS232 protocols, so that information can be transmitted with external equipment.
Because it's a passive electronic label, the energy needed to work with chips and storage in an electronic label is provided by a reader, which communicates with an electronic label through the principle of electromagnetic coupling, which is created by the reading instrument's antenna.
The high frequency electromagnetic field is generated by the antenna ring of the reader, and then the magnetic field runs through the space around the cross-section and the circle. According to the label's usage frequency 13.56 MHz, its wavelength is 22.1 m, far more than the distance of the reader's antenna and electronic tags, so that the inter-tangible electromagnetic field can be treated as a simple intersectional magnetic field from the reading machine to the antenna.
By adjusting the electron labels' antenna and capacitors to form a resonance circuit, aligning to the R/C specified launch frequency 13.56 MHz, the RFID tag reading card distance is proportional to the power transfer efficiency of the two sets of the wiring and electronic labels, which are at a positive level, as well as the distance between them, which is the reason for the limit in the RFID tag reading card distance.
For the RFID electronic labels used under 13.56 MHz, its maximum reading and writing distance is usually around 10 cm, and the current consumption of chips is roughly 1 mn. Because as the frequency increases, the electro-labelling loops required are electrons that show a decrease in the number of coils, typically at that frequency, with a typical Twist of 3-10 mm.
RFIDThe distance of the label reading card is not only related to itself, but also has a strong bearing on its environment. When using an electrons-coated radio frequency recognition system, it is often requested that the antennas of the reader or electronic tag be installed directly on the metal surface. However, it is impossible to install magnetic antennas directly on the metal surface.
Because the antenna magnetic fluxes through the metal surface generate a sensor vortex, which, according to the law of the subtidal law, can counter-acting the field of the antenna and cause a rapid decline in the magnetic field on the metal surface so that the distance between data reading by readers and electronic labels will be seriously affected, or even may be misread or read unsuccessful. Whether the magnet field created by the wire itself on the metal surface is the same from outside, it is also the site close to the metal plate (the electronic tag is on the metal surface).

Ms. Lei
Mr. Pang