Kyo Shincom uses RFID to track the antenna health of the wireless network
Industry News

Kyo Shincom uses RFID to track the antenna health of the wireless network

PublishedShanghai Zejie Smart Technology Co., Ltd.

One of the challenges in antennas is that equipment numbers, station accounts, port connections, and physical condition on site are often dispersed across different systems. The more important question about the old title “Kyoto communications using RFID to track the antenna health status of the wireless network” is how identification is combined with state observation, so that engineers can determine which device or relationship is wrong.

First, you'll explain the information boundary and then discuss technical value.

The reconstruction did not produce the full text of the original report, nor did it have enough material in hand to verify the scope and effectiveness of the project under the title, so that unverified deployments, partners or revenue figures are not used. The following is a technical analysis of antenna dimensions, which cannot be reported as an empirical report on this historical project.

Among the publicly verifiable information, KIMNET includes antenna monitoring equipment such as IMU-AL04A product presentations that involve observations of position, tilt and location. This suggests that “state monitoring” requires specific sensory and equipment capability support; this page does not in itself provide details about the implementation of RFID under the old title, nor should it be used to fill out non-existent project conclusions.

Device identity, connection and health signal need to be modeled separately

The device identity answer is "What antenna is this?" The connection answer is "Who port it received, which site it belongs to," and the health or performance signal answers "what is currently observed." RFID can be involved in identifying and maintaining records when it has the design of the appropriate system, but a normal identification label cannot directly measure the mass of wireless network coverage.

If you need to extrapolate the feed, the connection or the condition of the component, you have to indicate where the observation signal comes from, what sensor or test mechanism is used, and which failures are likely to produce similar performance. It is impossible to distinguish between a mask, direction, equipment failure, label damage and abnormality with the target at one point without reading the label. The diagnosis requires a combination of evidence, not translation of "not read" into "the antenna has been damaged."

Establishment of a baseline for installation to be eligible for change

Install and accept the object number, site, sector, port, installation time and authorized on-site records, and establish the necessary observation baseline under the same conditions. Next time, replace antennas, switch connections or adjust installation relationships, a version of the change record should be generated, not directly overwhelming old billboards.

For example, if the monitoring indicator changes after a maintenance, the system first needs to confirm whether there has been an authorization change in the field. If the equipment relationship is still pending maintenance, even if the measurement is fully correct, it can send the alarm to the wrong target. The identity is accurate and continuous, which is the basis for analysis of the change.

Translating the results of monitoring into work orders that can be executed by engineers

A useful warning should at least indicate which object is involved, what observations are made, when first appeared, whether it lasts, and what the most recent maintenance is. It should also allow engineers to record the results of the on-site review, the actual reasons for this and whether the equipment is replaced. If a worksheet is closed by clicking "processed," it is difficult for the system to distinguish between misreporting, recovery and real repair.

It is not appropriate to press all anomalies into a health score. Some observations may be delayed, some devices may be in maintenance and some fields may not have a baseline. Dissociating data from confirmed anomalies would avoid allowing an interesting green icon to express certainty beyond the evidence range.

Use maintenance results test system, not just recognition success rate

It is recommended that the equipment be evaluated for the reconciliation rate with the desk, the accuracy of the worksheet location, the number of duplicated assignment orders, the time required to confirm abnormalities and the causes of errors identified in the site review. The conclusion regarding coverage or radio frequency performance should be supported by appropriate tests and network data, which cannot be directly generated from identification records.

What really makes this kind of application worth thinking is how to build up the next reliable evidence for each maintenance. RFID can contribute some of the identity and process information, sensors, web indicators and engineering reviews to other observations. It is only by putting all kinds of evidence on the same subject and time line that “tracking health” does not become an unexplained label.

Extensions