What are the characteristics of the RFID smart asset management system? Automation and accuracy
RFID Knowledge

What are the characteristics of the RFID smart asset management system? Automation and accuracy

PublishedShanghai Zejie Smart Technology Co., Ltd.

The two core features of the RFID asset management system are automation and accuracy: bulk non-contact access to the transfer count is compressed from hours to minutes, and label coding is accompanied by a reading and writing check to increase the reconciliation rate from about 85 per cent to over 99 per cent. These two characteristics cut across the entire process from inventory entry, use, transfer to end-of-life.

Point 1: A count from a piece-by-case scan to a batch reading

The traditional disc is swept by people with a bar-coded gun, and the efficiency bottleneck is "targeting one by one." The RFID uses radio frequency signals, so long as it's labeled within the electromagnetic wave cover, the reader (the antenna plus the host) can identify multiple tags at the same time.

The passive label of the UHF segment (i.e., without batteries, powered by an electromagnetic wave from a reader) is common in actual projects, with 100 to 200 readings read at once, and a distance of between 3 and 8 metres, which can be read at a lot speed to dozens of times per second. Handheld terminals walk around the shelf, and in dozens of seconds complete the count of a shelf.

Warehouse operators know the difference: manually counting 5,000 items usually takes two to three days. A handheld RFID reader with fixed portal antennas can finish in half a day, without staff constantly bending down to scan.

Element 2: Positioning and status, from vague records to real-time tracking

Assets are often located in traditional billboards at a "in a warehouse" level. If the RFID system is compatible with closed antennas and positioning antennas (also known as RTLS, or real-time positioning systems), it can be positioned at regional or even room levels.

This is done by: deploying a reader antenna at the key entry/exit, automatically writing time stamp and direction when assets enter or leave; setting an array of antennas within the warehouse by area, which is roughly positioned with signal strength (i.e. RSSI values, quantitative indicators of weak label signals). When assets are moved out of the authorized area, the system alerts immediately.

For IT equipment, medical devices, tools, and assets that are vulnerable to loss or error, the core value of this real-time tracking is to turn "retroactive" into "interception." The best thing we've done for clients is here -- no more calls to ask where the notebook is.

Element 3: Data accuracy from manual entry to system validation

The biggest problem with manual registration of assets is not slow, but wrong. Miscleaning, leaking, re-cleaning, filling in the wrong information, each link may fail to match. The RFID system's advancement in accuracy comes from three mechanisms:

In practical terms, the increase in the accuracy of the count from about 85% to over 99% of the manual is a common level. This increase is not made by single points but by eliminating superimposes by errors across the process.

Point 4: Business processes run from manual to state-based

RFID is not just "labeling and cleaning." The real value is to get through business processes.

Each move becomes a record in the system, and complete electronic files are available throughout the life cycle of the asset. Follow-up audits or inventory counts, just call data without flipping paper documents.

Element 5: Aberrant detection from regular inspection to real-time early warning

In traditional asset management, the loss of assets often waits for the next inventory to be found. The real-time nature of the RFID system allows for the capture of anomalies in the immediate future:

These warnings are not after-action reports, but are sent directly to those responsible. The response speed is from "monthly count" to "minute interception."

How to choose and land

After these features are taken into account, there are a few things to be noted when you actually land:

  1. Frequency selection: UHF (UHF, 860 to 960 MHz) is used mainly in the country to read distance and lot speed; HF (HF, 13.56 MHz) is suitable for a short-range one-to-one view, such as door-barriers, payments
  2. Label matching: Metal surfaces are labeled as resistant to metal, general labels cannot be read; the liquid environment is also marked with a special label
  3. Antenna deployment: the warehouse gate, top shelf, access route is a mandatory location; intensive environment needs to be sensitive to interference between antennas
  4. System interfacing: label data will end up in ERP, finance or self-build systems. Interface stability is more important than RFID hardware itself

RFID asset management is not a set of hardware that is complete, but a full project from label selection, antenna deployment, business process combing to system integration. Shanghai-based Best Technology in its multiple industries, has found the label selection back to the system interface from field survey, runs through the complete landing process, and has built on these practical project experience with two core features: automation and accuracy.

If you have hundreds of assets, and there are signs of discrepancies, it's suggested to pilot a warehouse or type of asset, run the process and spread it. The value of RFID is "use it," put it in place, and actually use it, and it's very different.