RFID on the Production Line: Identifying Carriers and Tracking Work Between Stations
RFID Knowledge

RFID on the Production Line: Identifying Carriers and Tracking Work Between Stations

PublishedShanghai Zejie Smart Technology Co., Ltd.

In the discrete manufacturing scene, RFID is going to make it look like a real run for the carrier identification and process flow, not as a pile of equipment, but as a clear line to "which conveys which, what state after which?" Without any link, data will be broken; overcalculated, it will make the first line of operation heavy. Before you land, you can put the type of load, the process node, read and write points more important than purchasing hardware.

Point 1: Dismantling the identification.

Many projects are discussing the frequency labels, and the first step is to list the loads. Common ones are metal trays, plastics swinger boxes, SMTs, and tatter-sets, and tray-laying baskets. The impact of different materials on RFID varies greatly: metal surfaces shield UHF signals, plastic baskets change after acreage or high temperature, reading distance shrinks by about 30% (source: EPC Class 1 Gen2 labels in industrial settings, 2022).

Three separate confirmations for different sets of vehicles:

Element 2: Deployment density of reading and writing points and antennas

A process is accompanied by at least one fixed reading and writing point, which is an empirical value, not a technical rule. But the distribution depends on the course action: whether it's a forklift load or an AGV top lift, a hand-propelled cart or a chain-drive. The antenna selection varies widely in different ways.

It is suggested that priority be given to four reading and writing points:

  1. The throat tunnel to and from the workspace -- it's a guarantee that the load is recorded once in a process.
  2. Next to the key processing equipment -- like CNC (digital control machine) trap, SMT sticker feed.
  3. Quality control area and the area of separation for undesirables - avoid mixing of bad goods into normal flow routes
  4. The finished product library and the suspense stack - complement identification to avoid retroactive faults

The direction of antenna polarization is as vertical as possible and the vehicle moves, or there will be "over-points without reading." The metal environment is complex, with an aided reader to read it overload, which is more stable than simply increasing launch power.

Element 3: Nodal design for process flow

Process handoffs are most prone to problems when parts change carriers or production lines merge or split. For example, five parts on one pallet may go separately to assembly, packing, and after-sales, stages that are not consecutive. Link records at both carrier and part level.

Data model, it is recommended that each identification event be recorded as a line of water, including: a carrier ID, reading and writing point number, time stamp, read process state, associated batch or work unit number. The downstream system will judge current progress by the id+ time window, more reliable than simply relying on "last reading and writing" and avoiding leakage to cause a process jump.

Element 4: Alignment with MES, ERP

Agree on field mappings between RFID middleware, which cleans, groups, and forwards raw reader data, and the MES (manufacturing execution system). Typical fields are carrier ID, current operation code, operator, next operation, and status (awaiting processing, in process, complete, or defective). Field names are hard to change after launch. Spending one to two weeks on mapping can save three months of rework.

Define exception handling in the middleware as well. If two read points detect the same carrier within five seconds, which read takes precedence? Should three consecutive failed reads trigger an alarm? If a carrier leaves one operation but takes too long to reach the next station, should the system create a timeout work order? List these rules up front and review them one at a time to avoid repeated patches later. For similar projects, we normally deliver an exception handling matrix that lists scenarios, triggers, and system actions in a single table for the site team.

Element 5: The rhythm from pilot to bulk reproduction

Do not roll the system out across the shop floor right away. Pilot it for four to six weeks on one production line with a continuous process and relatively few carrier types, and verify all four points above. Focus on collecting three kinds of data during the pilot:

After the pilot inspection, it was extended to a full-scale workshop, and new problems were encountered when more load types were introduced, such as changing labels for higher metal loads. The last one was a cross-shop reproduction, and then the standard, field, training system was shaped. Shanghai-based RFID technology usually moved on three segments of the "Roadline - Demonstration Workshop - Full Plant Extension" approach, each with clear exit conditions, so that the project would not be half-completed.

End

The RFID line management is really on the ground, and hardware is the surface, and data stream is the skeleton. First, the load, read-and-write point, three things are modelled, then the device selection and system integration are discussed, and the sequence is countered to the project's shell. It is recommended that you start running from a continuous line of work, by measuring the pilot results of the three sets of indicators, reading and writing success, error rate, and staggering impact, and then expanding it after meeting the standard.