Fixed rfid reader installation specifications, antenna layout and contour circumventor elements
RFID Knowledge

Fixed rfid reader installation specifications, antenna layout and contour circumventor elements

PublishedShanghai Zejie Smart Technology Co., Ltd.

Last winter, Shanghai Zejie's project team retrofitted a third-party logistics warehouse in Jiangsu with UHF RFID. All four aisle entrances got fixed readers with four-port antenna setups. The design called for full coverage, but missed reads climbed above 8% after launch. After two days of troubleshooting, the team found the problem was not the reader itself, butThe adjacent antenna is read at the same time, overlays areas and labels respond to crashes. To enable a fixed RFID reader to perform design performance, the installation of specifications and antenna layout is key.

Survey phase: The most easily missed items on the scene

The reader has not yet been packed, so first take out the plan of the warehouse and load three items.

The first is...Tracks actually appear in the labelAnd the missing is the forklift charger -- when the forklift takes the battery, it takes the tray outside the alley door, but the plane map does not reflect this trajectory, and the reader is put in the alley door, and the forklift is not covered by the charger. The survey is conducted with a full access garage shift, marking all the locations where the labels may have reached.

Second,Metal structure and shield. The cargo is mounted, the conveyor belt supports, cable bridge, air conditioner windpipes reflect or absorb UHF signals near 915 MHz. We encountered a conveyor belt in the warehouse that was right ahead of the reader, which was thought to be no impact, debugging the shell and cutting off a large part of the main pedal of the reader. The final processing was moving the reader 1.8 metres upstream along the transfer belt, or putting suction material (cost lower than the mover, but less effective) on the corresponding casing.

Thirdly,Power and network linesFixed-type readers typically need PoE+ (802.3at) or an independent 24V DC power supply, around 1A for work. Once the antenna feeder is over 10 metres away and the LMR 400 coaxial cable is replaced with low-depletion, it's clear that ordinary RG58 has been decomposition at more than 10 metres. We have seen how to save things by using radio frequency as a web line, and the reading machine has a power of up to 3 metres of labels, which is difficult to return to once it is completed.

Fixed installation: hard requirements for the reading and writing body and feeder

The cysts of the reader are typically standard installed holes in the case, which are used in a fixed way.

In storage and manufacturing workshops,Install or wall up as much as possible with a guide.And avoid drilling directly into the shell -- the latter would break seals, and seriously affect dustproof water. The reading and writing levels are common IP54 and IP65, and the area that is installed in humid or multi-dust must select IP65, and then we'll have to screw up the head of the Glen in the cable.

Suggested length of the feed between the reader and the nearest antennaControls within 8 meters., the feedback curved radius is not less than 10 times that of the cable's outer diameter. Each feeder's frequency is fixed and protected from water at both ends, with a scrawling rectangular of about 0.5 to 0.8 calfm on the SMA interface, too loose, too tight to lift up the electrical resistance, signal performance is good and bad, no pattern is found.

Locality is often ignored, but what happens is a big deal.The cylindrical shell must be protected, and the ground is less than 4 om. We have had a debugging of the USB mouth that was burned directly because it was unlocated and the sensor electricity leaked to the net.

Antenna layout: distance, angle, polarization.

Antenna is the most expensive unit component of the system and the most easily wrong-assembled part.

Distance: A rule of thumb for adjacent antennas facing the same direction is to keep their centers more than four times the intended read range apart. For a 5 m read range, leave at least 20 m between neighboring antennas. That may sound generous, but the wavelength at 925 MHz is only about 32 cm, and coupling does not decrease linearly with distance. Adequate spacing is more effective than any shielding measure.

AngleThe radial direction of the adjacent antenna is as staggered as far as possible to 30 degrees. The three-way logistics warehouse programme was finally repositioned to two sets of antennas in the adjacent alley, one group heading east and the overlapping area at the entrance has been reduced by a third in an instant.

Polarization Directionis another detail often overlooked. Linear antennas are sensitive to tag orientation. They read farthest when aligned, while a 90-degree offset may cut range to 20–30% of normal. If tag orientation is unpredictable, such as when forklift pallets are positioned arbitrarily, chooseCircle polarized antennaMore secure. The peak reading distance for round polarization is shorter than that of the line, but it's wide-flung and can be read by forklifts, regardless of which direction they pass.

Calculate antenna mounting height carefully, too. For an application designed around a 5-meter read range,Antennas are proposed to be mounted on a 4-5 metre stairwell or beam.And it's a 10 to 15-degree downward slope to the trajectory of the label. It's too low forklift, too high to be over-opt angled, and the area around 1 metre below the antenna will form a close blind zone.

Serial disturbances circumvention: four layers of defense are easily tortuously folded

The essence of the scrambling is that "snatch" labels between readers, or one's loads interfere with the other's reception sensitivity. It's four layers of circumvention, and it's easy to get.

The first level is space quarantine.. The antenna spacing, angle, and polarization adjustments described above all create spatial isolation. Get this right and about 70% of cross-read problems disappear.

Second level is frequency quarantine.. China's UHF RFID band is 920-925 MHz, with 64 frequency-hopping channels. Assigning different channel sets to neighboring readers can prevent carrier conflicts. When EPC C1G2 Dense Reader Mode, also referred to as LBT (Listen Before Talk), is enabled, the reader first checks whether the channel is clear before transmitting. In that project we allocated 15 different channels to four readers, and interference metrics immediately improved by a level.

The third level is time-zone isolation.. In a scene that is heavily accessible to the library, you can stagger the launch gap of a neighbouring reader, like an A-reader in even seconds and a B-reader in odd seconds. This is a good way of doing things with high tolerance for missing reading, and be careful about the scenes that require high real time -- a staggered gap means that each reader has been cut half the effective read time.

The fourth level is power control.. In the same project, if a reader is used to read only a close-range label (within 2 metres), it will be reduced from 30 dBm (about 1 W) to 20 dBm (about 0.1 W), and interference with the surrounding reader will be significantly reduced. If the coverage distance is actually more than sufficient, otherwise it will not be lost.

And one thing is easy to ignore: between readers.If the line is over 50 meters, use a shield line.And the shield is located at both ends. Otherwise, the web line itself will become an antenna that picks up and magnifies the radio frequency leak between readers, creating a seemingly inexplicable string of disturbance.

Transfer of test collection: three sets of data to determine whether the installation is satisfactory

When the installation is complete, do not rush online and do a round of offline testing.

Group I: RSSI distribution. Linking the standard reference labels to a 0.5-metre grid in the area covered, with 100 per cent reading rate being measured as the coverage area. The degree of overlap between the eligible and the design area should be greater than 90 per cent.

Group II: Multi-label throughput. Place 30–50 tags 1–3 m directly in front of the reader and read them together. The test passes if at least 95% can be read within one second. The third-party logistics project mentioned above achieved only 70% at first, suggesting room to improve antenna placement or power.

Group III: Long-term stability. Let the system run 24 hours in a row to see if there is an intermittent leakage, or a false death of a reader. The problems with RFID are mostly intermittent and require long-run data to be exposed.

Replicable one-time installation

The transfer of the test collection does not mean that everything is good.It is recommended that routine inspections be conducted quarterly。

The inspection list can be streamlined, mainly by three things: to see if the reader's shell has been deformed or fractured; to screw the radio frequency link in a power outage and see whether it is loose; to allow the reader to read the reference label for fixed position, and to compare the historical RSSI values with any significant decrease --RSSI drops above 3 dB usually mean an antenna shift or a feedback problem.Further scrutiny is required.

A significant proportion of the problems with RFID are occurring in the day after tomorrow, like when a forklift crashes an antenna stubble and no one finds out, or when a radio frequency line is bit by a mouse on a cable bridge. We then added an action to that tri-logistics warehouse: each forklift has a collision recovery, matching the angle of the nearby RFID antenna. One year goes by, the system is clearly more stable than a project that is purely ex post facto.

The fixed RFID reader appears to be a physical work, and the real decision is to win or lose.Survey depth and antenna layout. These two steps are solid, and the subsequent debugging saves half of the time, so that the failure rate during the run-off can be below 1 per cent.