tag. Antenna Printing Probability Enhancement
Industry News

tag. Antenna Printing Probability Enhancement

PublishedShanghai Zejie Smart Technology Co., Ltd.
As the RFID market grew, so did the use of electronic labels. But the real obstacles to the development of the RFID industry were:TagThe price is still high, and the price of a print electronic label is highly desirable. Printed electronics are widely used in soft electronics, organic monitors, EMI control, paper batteries and RFID, where passive electronic tagging with RFID is the most difficult technical problem.
Printing process
The use of RFID's passive electronic label printing is commonly called "conductive silver glue." Because of the need to print silver powder, and because of the recent price hike in raw materials, the cost of silver glue is high, which has led to a real-time fall in the cost of printed electronic tags that have been at the forefront of manufacturing costs, but in the long run, printed electronic labels remain one of the best solutions for low-cost electronic labels in the future.
In printing, the print-printing process alone has four main categories of web version, dent, amphibious and ink spray, each of which is different in quality and cost, and if you add the ink and base materials to the ink, the electronic tagging process and the material characteristics mix will determine how the electronic labels are produced.
Printed online
The print program for the RFID electronic labels uses the most of these aluminum examples, with the web-based printing being the use of a conductor ink to run through the net by razor on the other side of the web, while the ink is applied through the specter gap of the net that is painted on the web page and is sticky on the base of the printed. The ink is more sticky on the web-based version, and can be as thick as 100 m, while the print film on RFID electronic tags is only about 8-12 m thick, followed by drying up with the UV, IR and heat wind.
Dimple printing
Damp printing is the thin, dented version of the metal (docked) that will be printed on a printer's tampons, which will be printed in ink and then printed on the base, as shown in figure (2). The dimpled ink is more sticky than the moustache of web-based printing ink, the most accurate control of the oil membrane thickness, and meets the thickness requirements for RFID ZZZQQZ production, and the speed of printing is much faster, it is better suited to large print production, with the disadvantage that the equipment to be invested is more expensive.
Cam Printing
The ink in the ink is lower than in the dent, and the ink in the ink in the ink is much less thick than in the first two, and the most difficult problems with printing the silver glue are to overcome, but the price competitiveness of printing RFID tag directly on the box is not comparable to that of the first.
Inkjet printing
The development of ink-jet printing technology, which has been developing for almost a decade with a maximum print accuracy of 50 μm for large ink-jet printing equipment, is also the most likely to succeed in making IC circuits directly printed during their production process, but the disadvantage is that they are slow, and equipment and ink costs are the highest of all printing processes, while ink-plugness is the lowest of all four, and film thickness control is the highest.
Ink properties of silver-jet-controlled ink
The current supply of conductive silver glue is based on the US, European manufacturers and Japanese and South Korean producers in Asia, with its ink properties mainly being silver powder, while the size of the composition of silver powder determines its conductive resistance. The size of the silver powder particle diameter is also key to determining the average resistance of their printing resistance, as shown in table (1) for a comparative list of several products in the current market that have high and long dry-cooked and longer than usual printed oil inks, and newly developed conductive silver ink properties tend to be low-temperature dry and slow-drying energy and environmentally friendly.
Bottom
The most easily overlooked part of the electronic label printing process is that the base of an electronic label (substrate) typically has a passive electronic label of more than PVC, PET, white paper, waffles, etc., but if used in the UHF band, the media of the bottom material will significantly affect the resistance of the electronic label to RF[5], so this factor should be taken into account when designing the electronic tag antenna.
When the bottom paper is printed electronically, it is very big and spread irregularly. When the ink is printed, the ink penetrates into the inch, causing the electronic tag antenna to resist the distribution of the same amount, which is more problematic when the frequency is higher.
Good rate
Besides the fact that RFID tag is read in the finished product, users are more concerned about the good rate of application, which is known as a steady distance from reading, and the key reason for this is resistance by the completed product to the RF. And the hard work on printing antennas, the chip wrapping and ink properties are important factors in determining the life of such products.
Controls are resistant.
The RF impedance of a printed RFID tag antenna depends on factors such as how evenly the ink solids are distributed, the thickness of the printed film, and the dielectric constant of the substrate [7]. Printing professionals know that color and film thickness vary to some degree from the first print to the last. Quality differences in the substrate can also change its dielectric constant. Together, the two variations may compound or offset each other and can push the printed antenna's impedance out of specification, producing rejects. The effect is relatively minor for printed passive HF antennas, but the likelihood of rejects rises sharply with printed passive UHF antennas. Even when the combined effect of the two process variables leaves antenna impedance within specification, the finished UHF RFID tags can still differ in read range.