Process resolution for rfid label production: inlay seal, modulate and finished product testing
RFID Knowledge

Process resolution for rfid label production: inlay seal, modulate and finished product testing

PublishedShanghai Zejie Smart Technology Co., Ltd.

The core findings are first put forward.

The core of the RFID tags is determined by three processes: inlay sealing (the integration of chips and antennas into a minimum functional unit available), modulation (to various finished forms by size), product testing (corresponding to bad products and verifying performance). These are stable, directly determining the distance from which the labels read and write, consistency and goodness. To do RFID labels, not so much as being sophisticated, but rather matching the parameters of the different processes, fitting the appropriate packagings, and checking the closed ring. We have done thousands of batches, the deepest part being: the front seals are one thread, and the backtrack tests are not going to be saved.

Inlay seal: The first chorus that binds to the antenna

Inlay (the Chinese custom is "inlay" or "complex layer") is the core layer of the RFID label, consisting of face, chip, antenna (coloured or aluminum-coated), and detached paper. This process is not well done, and everything else is empty.

The choice of chip binding methods

There are two main types of mainstream: Flip Chip (rewind welding) and Strap Attach (aluminium wire binding). The former are suitable for large quantities, the scenes with small chips (e.g. Impinj Monza R6 sizes of about 0.5 mm x 0.5 mm), the speed of containment, and the low single-point cost; the latter are appropriate for a larger chip, which is a correspondingly demanding industrial scenario.

In production, the temperature profile and pressure are the two most common sources of problems. In flip-chip bonding, for example, exceeding the temperature recommended in the chip datasheet, typically around 300°C for 0.3-0.5 seconds, can damage the chip. A lower temperature can result in higher contact impedance, reducing read range by 10%-20%.

Matching of materials and test of incoming material

The communicature constant of the face, the thickness of which directly affects the antenna coordination frequency. The same inlay design, using 50 m of PET surface and 75 m of PET, will shift the central frequency from 5 to 10 MHz, and the antenna size will have to be resized. So the reprogramming frequency must be re-measured for the material batch.

Shanghai uses the web analyser to test 5-10 samples before each batch is online, to confirm the conjunctive points and then turn on the engine, avoiding mass return. This step will take no time, but it will save a lot of later check-ups.

Motangular: Key conversion from continuous scroll to finished product form

It sounds like "die-cutting," but it's about precision, the life of a knife, material adaptation and so on. The smaller the RFID label size, the more complex the shape (e.g. an alien label with round angles), the harder the molar is.

Knife Model Design and Control of Public Service

Common tag size tolerance is within ±0.2 mm. Too tight and yield plummets; too loose and placement drifts. Inspect die height, blade angle (usually 50°–60°), and edge wear regularly. A new die typically lasts 500,000–1 million cuts. Adjust the anvil roller gap as needed for material thickness.

Layout and material utilization

Layout pitch determines material utilization. The inlay pitch is fixed by chip bonding spacing, but staggered layouts for finished tags can improve utilization by 5%-15%. For example, alternating rows in opposite orientations can raise space utilization from 65% to around 78%, but requires more precise die-cutting registration.

The pits that are easily pedaled by the modular link are inlay antenna lines that deviate from the modular line (i.e. "chip to antenna"), leading to the failure of the label. This deficiency is a dysfunctional, much worse than the appearance and must be intercepted at the back of the test.

Final test: Bad stuff is not stopped, and the work ahead is wasted.

Final Inspection is the last line of defence, divided into three categories: physical inspection, electrical performance testing and functional reliability.

Appearance test

Use a CCD vision system to inspect for burrs along die-cut edges, damaged face material, chip misalignment, and print defects. The typical tolerance for chip misalignment is ≤0.1 mm; tags outside it are rejected. Burrs longer than 0.05 mm also affect tag application.

Electrical performance and functional testing

Each label is tested for reading and writing, confirming that the EPC area, TIID area, can read and write normally. Read distance is tested under a fixed field power using the standard reference tag (reference tag), such as the 866-928 MHz frequency segment commonly used in the UHF frequency band to read distance, with deviation from design value ±20% of the internal value being judged to be satisfactory.

Common sampling plan for volume production: Set the AQL (acceptable quality level) between 0.65 and 1.0, adjusted to customer requirements. See ISO 2859-1 for implementation (source: ISO 2859-1:1999, single sampling plans for normal inspection).

Reliability test (scrudent)

Not every one of them, but a batch-based sample, for example 20-50 sheets per batch to do high temperature and humidity (85°C/85% RIH, store 168 hours), bending, stripping the ion. This step is used for batch reporting to clients, and it's also the basis for backtracking problems.

A few experiences from the rewinding.

After years of RFID tagging, several experiences can be used directly:

Proposals for action

If you are going into the production of RFID labels or if you experience a rate of good rate fluctuations on existing production lines, it is suggested to start with these three steps: first, complete the recording of parameters for existing processes, covering at least 20 batches recently; secondly, classify bad goods by type of defect, which is a percentage of each category, and the first three categories add up to explain 80 per cent of the problem; and thirdly, what parameters need control in respect of the first three defects, which are often temperature humidity, pressure, and slash.

The RFID label is not high-tech, but it's patient in the details of each process. It stabilizes the encapsulation, the agility, the three-step parameters and the process, and it strikes a balance between cost and good rate, which is what industries are saying about "stabilization."